2006-2014 Yamaha RaptorRhino 700 10.75 105mm +3mm oversize bore x 84mm stroke (727cc) piston kit
Please allow up to 2 weeks for delivery. If it is any longer, we will contact you.
Feel free to contact us to confirm delivery time before you order.
For shipping cost -add all the products you would like, then navigate to the shopping cart to calculate shipping quote.
2006-2014 Yamaha RaptorRhino 700 10.75 105mm +3mm oversize bore x 84mm stroke (727cc) piston kit
|
Make |
Yamaha |
|
Engine Size |
700cc |
|
Model |
Raptor / Rhino 700 |
|
Year |
2006-2014 |
|
Bore (mm) |
105mm |
|
Comp Ratio |
10.75:1 |
|
Piston Part Number |
M1041A |
|
Gasket Part Number |
C3144 |
|
Conrod Part Number |
PSR5023 |
|
Pin Part Number |
W905-2250-15CP1C |
|
Locks Part Number |
905X073 SWL |
|
Rings |
CPN-4134 |
|
Shelf (RPO) or Made to Order (MTO) |
MTO |
Proudly made in the USA by CP Carrillo Pistons!
- Fully CNC machined
- Balanced to +/- 1 gram
- Double forced pin oilers
- Forged from high strength 2618 alloy
- Designed for maximum performance, horsepower and reliability
- Complete kit includes two pistons, ring sets, wrist pins and clips
- Follow ring end gap and piston to cylinder clearances as per the supplied instructions
| Product Name | 2006-2014 Yamaha RaptorRhino 700 10.75 105mm +3mm oversize bore x 84mm stroke (727cc) piston kit |
|---|---|
| Brands | CP Carrillo |
Delivery & Freight
We are an Australian-based company that ships items nationally and internationally, usually within 48 hours of receiving your order. High-value items shipped internationally are sent via DHL Express, while lower-value items are sent via Australia Post Express unless otherwise instructed.
You can calculate shipping rates inside the shopping cart. After adding all the products you would like, navigate to the cart and click the ESTIMATE SHIPPING & TAX link. .
If you only see the Click and Collect shipping option, it means that your address was not validated correctly.
If you have issues calculating freight, please get in touch. We are happy to help.
Disclaimer:
Product images are for description purposes only. Actual product may vary.
Shipping calculations available at checkout.
If you are unsure, get in touch by emailing [email protected], messaging us on Facebook, or phoning us at +61 7 5645 1333 (8am to 2pm AET).
What information do I need to match these pistons to my engine?
You need the engine code, bore size, stroke, rod length, pin diameter and target compression ratio. These determine the correct piston compression height and crown design.
How should ring gaps be set for these pistons?
Ring gaps must be set by your engine builder based on fuel type, boost level and the intended rpm range. Forced-induction engines usually require larger gaps.
Are forged pistons suitable for street engines?
Yes. Forged pistons handle detonation and high cylinder pressure better than cast units. Your builder should set the piston-to-bore clearance to suit your application.
What is the recommended bore clearance for the M1041A piston kit?
For the M1041A piston kit, the recommended bore clearance should be set according to the specific engine build and intended use. Typically, a clearance of 0.0025" to 0.0035" is a good starting point, but always refer to the manufacturer's guidelines and adjust based on your engine's requirements.
What type of fuel is recommended for the 10.75:1 compression ratio of this piston kit?
For the M1041A piston kit with a 10.75:1 compression ratio, it is advisable to use high-octane fuel to prevent knocking and ensure optimal performance. A minimum of 95 RON is recommended, but check your specific tuning setup for the best results.
Do I need to modify my cylinder head for the M1041A pistons?
Depending on your specific engine setup, you may need to check for clearance between the pistons and the cylinder head, especially if you are using aftermarket components. It's crucial to ensure that there is adequate clearance to avoid any potential contact during operation.
How should I break in the engine after installing the M1041A piston kit?
After installing the M1041A piston kit, a proper break-in procedure is essential. Start with a gentle driving style for the first 500 to 1000 km, avoiding full throttle and high RPMs. Gradually increase load and RPMs while monitoring engine performance and temperatures.
What is included in the M1041A piston kit?
The M1041A piston kit includes two forged pistons, a complete set of rings, wrist pins, and clips. Ensure you have all components before installation and follow the provided instructions for proper fitment and clearances.
